ISR and Voice Enabled Routers with CME (Call Manager) > Cisco 2811 256D/128F w/ CME 8.6 + PVDM2 + FXO Card
Cisco 2811 256D/128F w/ CME 8.6 + PVDM2 + FXO Card

The product you selected is currently unavailable.

Orig. Price: $179.99
Sale Price: $139.99
Availability: in stock
Prod. Code: 2811-CME-FXO

This is a Voice-enabled Cisco 2811 ISR Router loaded with CME 8.6 (Cisco Unified Comm. Manager Express). IOS version is 15.1.4.M (Adv. Ent. Serv.) and it also includes CCP 2.7

Memory Size is: 256 Mb. DRAM and 128 Mb. Flash.

This 2811 Router includes the following Voice Cards and Modules:

- FXO Analog Card (needed to make Phone Calls outside the LAN)
- PVDM2-16 Module (needed to enable Voice Cards)

These Voice Modules (FXO Card and PVDM Module) enable this Router to make & receive Phone calls through an External Phone Line!

Note: An active Phone Line is needed to make/receive External Phone Calls. The Phone Line can be implemented in multiple ways: standard Land Line, Vonage, Magic Jack, etc.

The Router is shipped Fully Configured and ready to use in a VoIP Phone Network (SCCP & SIP)

Note: An IP Phone is also needed to make/receive Phone Calls, because the Router is configured to redirect the External Phone Line to a specific Internal Extension.

Features Summary:

These are the main features of this 2811 Voice-enabled Router:

- 256 Mb. in DRAM and 128 Mb. in Flash
- Loaded with CME 8.6 (Cisco Communications Manager Express)
- Loaded with CCP 2.7 (Cisco Configuration Professional)
- 2 x Fast Ethernet Interfaces
- IOS 15.1.4.M Adv. Enterprise Services (needed for CME 8.6)

- FXO Analog Card (needed to make Phone Calls outside the LAN)
- PVDM2-16 Module (needed to enable Voice Cards)

The 2811 supports up to 35 IP Phones and up to 144 Virtual Ports (Virtual Ports determines the Max. # of Directories)

A Bonus Disk is included with this Router!

The Disk includes all Software elements: CME 8.6, CCP 2.7, IP Communicator, IOS Images & dozens of IP Phone Firmware Files!

IP Communicator is a Software-based Phone (or Soft-Phone) that can be used to make actual phone calls. You can even install IP Communicator on more than one PC and thus simulate a Phone Network without actual IP Phones!

Moreover, it supports multiple lines and directory numbers and therefore it can handle multiple calls!

The Disk also includes a Lab Exercise Guide (eBook in PDF format): CCNA Voice Lab Manual

Configuration/Operation:

With this Router you can implement a LAN-based Phone Network that can also make & receive Phone calls outside the LAN using the Voice Modules included with it.

To connect IP Phones to the CME Router you would need LAN Switch; if possible with PoE (Power over Ethernet) which would eliminated the need for Phone Power Supplies.

One port of the Switch would be connected to the Router's Ethernet interface, while the other ports would be used for the IP Phones.

Detailed configuration is needed in the Router (6 sections) in order to support SCCP & SIP Phones
But this configuration has been already done on this Router!
So if you to add a PoE Switch and IP Phones, you'll be ready to start making phone calls!

No other Hardware is required to make calls between the Phones connected to the LAN!

The FXO Card and the PVDM Module are only needed to make calls outside the LAN.

Note: As mentioned above, an active Phone Line is needed to make/receive External Phone Calls.
A regular Phone Cable, with RJ-11 connectors at both ends, is needed to connect the FXO card to the External Phone Line.